24V Continuous 10m iP67 RGB 5050 LED Strip - 30 LEDs/m

24V Continuous 10m  iP67 RGB 5050 LED Strip - 30 LEDs/m

LED Montreal allows you to fully enjoy the benefits of the 24V Low Voltage technology with this outdoor rated continuous 10m RGB LED Strip Kit. This kit features a CDNLUX RGB LED Strip at 30 LEDs per meter and is the perfect lighting accessory for your gazebo, your outdoor terrace or under the awning of your RV.

The kit includes: 

1 - 10m RGB CNDLUX iP67 Outdoor Rated LED Strip – 30LEDs/m
1 – 24V 96W Class 2  iP67 Outdoor Rated Power Supply
1 – RF Multi Zone Controller
1 – RF Multi Zone Remote 

The technical stuff: RGB Stands for Red-Green-Blue. 5050 RGB Chips give a 120-degree light beam and feature each of these 3 colors of LED lights within each chip: This allows to create up to two million different colors by mixing the red, green and blue at different levels. The amount of colors that can be achieved will depend on the RGB controller that you use. Note that the RGB Chip does not create a true white. Should you want to use your Strip to both enhance your décor and get an ambient white light, we strongly suggest using our RGBW Strip that includes a white LED diode within the 5050 chips. 

RGB LED Strips have a 4-wire connection, meaning that they can only be operated through an RGB controller. The controller will allow you to dim your strip and change colors manually or through automated color change patterns. The strip cannot be dimmed through a standard wall dimmer. You will find all the specs at the bottom of this page. Forecast a power supply at 24VDC of 9W (750mA) per meter for your installation. In other words, if you intend installing the whole spool, we recommend using a 96W power supply. As stated earlier, this strip comes in a 10m spool. 

You can customize your LED Lighting set up as this Strip can be cut every 5 LEDS. The RGB LED Strip is flexible vertically but cannot be bent horizontally. Should you need to bypass an obstacle or turn a corner, we recommend removing the iP67 sleeve with an x-acto knife and solder 4 strand wire onto your Strip. Soldering ensures a solid connection and minimal voltage loss. Use type 1 Silicone with our waterproofing caps to ensure a weatherproof connection. Quick connectors are available but are not recommended for outdoor usage.

Your RGB LED Strip is equipped with a high-quality 3M adhesive. This adhesive is intended for outdoor usage on a smooth and clean surface. We suggest using a LUX740 extrusion if you want to install your Strip on concrete or any surface where sticking a Strip is not possible. 

The CDNLUX Difference: 

There are many features that make the CDNLUX LED Strips stand out from the competition. First, the PCB (Printed Circuit Board). We use custom PCB that ensures a consistent brightness throughout the Strip. Unlike cheaper strips that can be found on the market, the CNDLUX Strip will allow you to connect to 10 meters in series without losing brightness. 

You will also be happy to know that CDNLUX uses Super Bright chips on their LED Strips. This means that you will get the best brightness for your money out of each LED Chip. As a matter of fact, CDNLUXChips are 25 to 30% brighter than chips used on lower prices LED Strips that you would find on discount websites. 

CDNLUX LED Strip are cULus Listed. This means that they have been tested for electrical safety according to Canadian Standards when powered with a compliant Class 2 Power supply. It also means that they will pass the toughest building inspections both in Canada and the USA. 

CNDLUX uses iP67 Technology on their outdoor Strips. Lower end strips are waterproofed with silicon glue that tends to crack and lose its transparency with time. Furthermore, the silicon glue is only laid on top of the strip, leaving the back of the circuit board to humidity. The CDNLUX iP67 technology protects your strip all around with a silicon sleeve that remains clear and flexible through time 

With CDNLUX, you’re never on your own. Your LED Strip comes with the tech support and troubleshooting that you need to complete your project. All our representatives are based in Canada and are fully bilingual. You can reach us by email or by phone during business hours. Definitely not something you would get from an overseas seller on a discount website. 

The cETL Certified 96W Transformer included in this kit is also designed for outdoor use. Its sturdy aluminum housing is weather-resistant and uses ambient air to cool down. It is not advisable to put it in a waterproof box. Its high voltage (120VAC) connection is made up of 3 wires that must join your 120VAC power via a waterproof junction box. We also recommend a junction box for the 24V DC connection of your 96W Power Supply. The junction box will also allow you to protect your Controller as it is not waterproof.

The Multi Zone controller completes this high-end kit. With a range of 30m via its remote control or WiFi adapter available, it is both powerful and easy to use. We invite you to visit this page for more details on Multi Zone systems.

LED Strip
Brand: CDNLUX
Model: MTL-FP10AGIWM-30ARGB
Certification: cULus E498952
Voltage available: 24VDC
Chip: Epistar 5050 RGB SMD
Lighting angle: 120 degrees
Can be cut: Every 5 LEDs (17 cm)
Strip Width: iP67: 13mm
Self-adhesive
Power consumption: 7.2W / meter
Recommended transformer: 9W/ meter, must be powered by a Class 2 transformer
Operation temperature: 40C to -10C
Suitable for dry, damp and wet environment
Dimmable: Yes, through the remote/ wall panel
Heat Dissipation: Not necessary 

24V 96W (4A) LED Driver
Input: 100-265VaC 47/63Hz 2.0A
Output: 24Vdc 4.0A
Max.Output Wattage: 96W
Dimensions 163 mm (186 mm including brackets) x 69 mm x 43 mm
Certification: cETLus Class 2

Multi Zone Controller
Dimensions : 85mmx45mmx22.5mm
Working Voltage: 12- 24V DC
Maximum output: 6A/ Channel  10A Total
Control Range: up to 30m
Note that the controller is not waterproof and must be installed inside a PVC Junction box (4’’x 4’’ recommended).