24V 7.5m iP20 RGB+W 5050 LED Strip - 60 LEDs/m (Strip Only)

24V 7.5m iP20 RGB+W 5050 LED Strip - 60 LEDs/m (Strip Only)

Standard RGB Strips are appreciated because of their wide variety of colors but do tend to cause a slight problem when the time comes to reproducing white. Since the Standard RGB Strip uses a mix or Red, Blue and Green to makes colors, its version of the color white tends to be very blue or even purple. 

The cUL Certified RGB + White Strip kit from LED Montreal will output the full RGB Spectrum PLUS a true White. This chromatic prowess is achieved with special 5050 Chips that integrate 4 separate lights: Red, Green, Blue and White. Each Strip features 450 Chips over a span of 7.5 meters, or if you prefer, 60 LEDs per meters, giving this Strip an amazing brightness, no matter what color you select. Note that the RGB+W Strip will only produce one shade of White. You will be able to select the white you prefer in the pull down menu when placing your order.

When used with the FUT038 Controller, your Strip will produce one color at a time. Therefore, you cannot obtaine a white and a color at the same time. This limits the Strip's consumption to 10W/m. We then recommend using 12W/m on your power supply.

When used with the WL5 - 5 in 1 Wi-Fi Controller, you will be able to mix the white and the colors in order to obtain a more pastel shade. At that point, we recommend using 18W per meter for your power supply.

This iP20 LED Strip does not offer any water protection. iP20 strips are ideal for indoor usage in aluminium profiles. Moreover, no connectors are available for this type of strip. For outdoor applications where the strip will be directly exposed to the elements, we recommend iP67+ grade strips.

Note that the RGB+White Strip is offered in 24V, you cannot use a 12V power supply for this Strip.
Furthermore, you will notice that this Strip is 12mm wide, which is wider than the Standard 10mm 5050 Strip. As well, given that this Strip offers 4 colors, it features 5 connectors unlike the Standard RGB Strip that normally features 4 connectors. This being said, solderless connectors are yet to be made available for this product. Should you require to cut and reconnect your RGB+White Strip, it can be cut every 6 LED (10cm) and we suggest soldering wires directly on your Strip.

Specifications:

Brand: CDNLUX
Model: MTL-FP12AGIDJ-60ARGBW
Certification: cULus for Canada and USA E498952

Chip: Epistar 5050 RGBW SMD 4 in 1
Chip density: 60 LEDs per meter
Can be cut: All 6 LEDs (100mm)
Length: 7.5 meters
Width: 12mm
Height: 2mm

Voltage: 24V DC
Power Consumption: 9.6W/m at 24V on Multi Zone Controller
Recommended Power: 12W/m at 24V on Multi Zone Controller
Recommended power supply for 7.5m: 96W, Class 2 power supply required
Typical luminous flux on white: 400 Lumens/m (will slightly vary depending on Kelvin degrees chosen)
Available colors: RGB + White (1800K, 3000K, 4000K or 6000K)
CRI: 80+
Lighting angle: 120°
Lifespan: 50 000 Hours

Self-adhesive: 3M
iP rating: iP20
Suitable environment: For indoor use only
Operating temperature: 40C to -10C
Connections included: 5 wires (17cm) on one end and 5 wires (17cm) on the other end
Dimmable: Yes, with a low voltage dimmer/remote combo
Heat dissipation: Must be installed on a heat dissipating surface or in appropriate aluminum channel

RGBW-24V-5050-LED-Strip-EN-CDNLUX.pdf